Hours of operation
Monday
Tusday
Wensday
Thursday
Friday
Saturday
Sundays
- 9am to 6pm
- 9am to 6pm
- 9am to 6pm
- 9am to 6pm
- 9am to 6pm
- 9am to 2pm
- Closed
Or alternatively you can email us 24/7 at info@rscustoms.co.uk or via our contact page

To simply make a booking Call us on
01274 572 000

Film Care FAQ's.

This page contains answers to commonly-asked questions about window film.

Black Dotted Edges on Car Windows?

Most cars have a black ceramic edge on the rear window. Sometimes this ceramic edge is straight and flat, sometimes it will have a dotted edge. These black ceramic dots are quite thick on most cars and prevent the window film from sticking to the area between the dots. This results in a whitish looking strip trimming the glass which is unavoidable.

Imperfections in Window Film?

A certain amount of small bubbles may be apparent in a window film installation and is quite typical. As a general rule one should stand at least a few feet back from the window and see if these micro-bubbles are still visible, also pre-existing flaws or scratches and metal deposits on the glass are often much more noticeable after the windows are tinted. However, it is important to keep in mind that we do our absolute best to install your tint using industry standard methods and care.

One or Two Piece Installations?

When possible we prefer to install rear windows in a one-piece installation. It may be necessary for certain vehicles to use a two-piece installation as a last resort. A two-piece install consists of two strips of window tint used to cover the rear window which is seamed along a centre heater line and should be unnoticeable for the most part. Two-piece films are considered standard and quite acceptable although we use a one-piece whenever possible for aesthetic reasons.

Is My Window Film Scratch Resistance?

Modern films have excellent scratch-resistant coatings. Older films had no scratch resistant coatings and some were ruined the first time they were cleaned unless extreme care was used. Today's films have very hard scratch resistant coatings that allow for normal cleaning. The manufacturers recommend that no abrasives be used. A scratch resistant coating is not a scratch proof coating, care should be taken when working around filmed windows with paint scrapers or other metal objects.

Film Peeling and Immune to Bubbling?

All our window films used are scratch resistant and do not fade, peel or bubble like other films. This will ensure that high quality finish will remain.

Window Operation?

We recommend that you do not open your windows for at least two to four weeks from the time of installation. Window films generally take a few weeks to cure properly and adhere to the window. Opening a window prematurely can lift the tint requiring you to bring the vehicle back to us so to reapply the film or possibly even replace it at an additional charge.

Rear Demister Distortion?

At night you may notice that the light from headlights will reflect off of the rear demister lines. This is caused by the film having to bend slightly around the raised demister line, it varies from car to car, and there is nothing that can be done about it.

Cloudy Appearance?

During the film installation most of the moisture will have been removed, the small amount remaining will leave small water bubbles or a slightly cloudy look. This is normal and should be expected. Do not attempt to pierce a water bubble during the dry-out time. Water bubbles and the cloudy look will eventually dissipate. Attempting to pierce a water bubble will damage your film and is not covered by the warranty. Window films usually take a few weeks to fully cure and may have a milky look until then.

Climate Conditions & Dry-Out Time?

Certain climate conditions can extend the dry-out time for as long as 30 to 60 days after installation. Cold and non sunny weather conditions can lengthen the dry-out time whilst warm weather and direct sun light exposure will shorten it. The dry-out time for metallized high performance films will always take longer than conventional non reflective film. If slow drying occurs, do not become alarmed. The trapped moisture will dry-out completely.

Window Film Maintenance?

Do not clean the film until 30 days after installation. This will help secure proper curing of the special mounting adhesive to the glass. Window film may be cleaned with a soft clean cloth and plain water mixed with a small solution of plain fairy liquid. Ammonia products should not be used.

Address:
424A Great Horton Road
Bradford
West Yorkshire
BD7 3HS

tel. 01274 572 000
Over 15 years of experience
Our products offer far more than just good looks. Today, you and your loved ones can enjoy protection from heat and glare and ultraviolet radiation just by having Solartint installed on your car windows. Why go anywhere else, stick with the name you know and trust.